Simplest multivibrator,mains operated

            Simplest multivibrator,mains operated(tested OK)

             I have been  thinking of a simplest alternate led flasher with main supply 230V ,without any transistor since last few months.After many  days  of trial and error,at last i have succeeded in that task. This is a simplest mains operated  multivibrator  without any transistor. ckt working well  fine for last few  months continuously.Cost of this  comes  around 6 to 7 Rs  or less only.

When apply 230V,Cap c1 starts charging.

while cap charging,led2, (series with cap) lights. DB3  get less than 30V while cap charging and does not conduct. After full charge of cap, diac conducts and  led1( series to diac) lights,n cap discharge thru 1N 4007 ,that time LED2  light get dim ,which gives alternate blinking effect.

1.8K Resistor series to led1 is more than the requirement ,but given for matching the light intensity with LED2. 

                                                         
                                                                            circuit  (click)

             R1-47K,R2-1.8K,D1,D2-1N4007,D3- DIAC DB3,C1-47uF/63V,

                        Thanks& regards

                        Vineesh kodambattil

simplest waterlevel controller with high low voltage cutoff

     simplest water level controller with High/Low voltage protection(tested OK)

                                          this is a  ckt for a very simple and cheap water level controller. This  ckt is only a basic portion of my own marketed product having unsafe voltage cutoff ,dry run cut off and LED & alarm indications and overall protection .Any way, given ckt includes automatic water level control and high /low voltage cut off. sorry for cannot post  the entire ckt  due to limitations.WATER LEVEL CONTROLLER  ckt is  not new concept since we can find 100s of ckts  for water level controller in many sites and texts.But This ckt is  simplified with least no: of cheap components. water level sensing and high voltage sensing is doing  with same transistor. I used to put all my ckts in observation for a few months and found this ckt OK. but recently some problems highlighted by some customer,which i will definitely write down  the end of this post.

CIRCUIT DESCRIPTION

When the water level in over head tank is sufficient , points B & C  are closed through water and keeps T2   in ON condition .So  T3 will be off , resulting the motor in off condition. 

When water level lowers  below  B &C,  T2  gets off  and   T3 on, which  switches  the relay and  pump ON (pump connections not shown in ckt). Pump  get off  only when water  rises and touch the point  A  only , because point C becomes  neutral condition when T3 get ON. The pump  switches on again only when the water level comes down below B & C .

Presets VR2 is to be set to a high voltage cut off, say 250V when the voltage rises above 250V during pump ON  condition, T2  gets ON, and relay  off.

Preset VR1 is to be set to a low voltage cut off say 170V. T1 will be ON until zener z1 loses its breakdown voltage when voltage lowers to 170V,  Z1  will not conduct and T1  stays OFF, which delivers  a base voltage  to  T2 , resulting relay off.

T2 is handling the major role in this ckt. (high voltage cut off boards based on transistors,available in market can be easily integrated to this ckt)

Electronic components in this circuit worked very fine, but recently some  problems were  observed:

1) Minor deposits on sensor wire due to electrolysis in water, needed to be cleaned in 2-3 months( this problem is minimized  now by applying  ac voltage to sensor wire by means of additional ckt, which  will be posting  later)

2) Due to relay contact terminal sparks, generated every time during initial current pull of pump, contacts get worn out gradually.which tend to heat the pump because off in-sufficient  current flow to pump  (observed, new pumps works fine. older pumps heats up more) .

For avoiding this problem, additional motor starter  must be used, so that relay's function is limited to control the motor starter only, and pump never heats up.

                                           circuit( click)

PART LIST

R1,R11   - 100K

R2,R4,R7,R9,- 1.2K

R3  -10K

R5  -  4.7K

R6  -  47K

R8,R10  -10E

R12  - 100E

C1   -   4.7uF/16V

C2   -   220uF/25 V

D1,D2,D3,D4- 1N 4007

T1,T2   -     BC 547

T3          -    BC 639( try 187 )

Z1,Z2-    Zener 6.3 V,

VR1,VR2- 10K PRESET

RL - Relay 12V 200E, > 5 AMP CONT ( According  to pump HP)

                                                          Thanks & regards

                                                          Vineesh Kodambattil.